Bathroom Stub Out
Asked by: Ayyub Schafhauser
asked in category: General Last Updated: 5th February, 2020
What does stub out mean in plumbing?
Stub Out. The pipes that go to the toilets, sinks, showers and drains--as well as any pipes that vent to the roof--must be in place and tested before the walls are added. The process of laying these pipes, and putting protective plugs or caps to keep building debris out, is called a plumbing stub out.
The plumbing stub-outs are the end result of the rough-in phase of plumbing a residential or commercial building. They are usually installed while the walls are still uncovered; and after the drywall work and painting is complete, a plumber comes back and hooks them up to the plumbing fixtures.
Secondly, how far should a stub out extend through a finished wall? Like the supply stub-outs, the drain stub-out extends from a fitting -- usually a sanitary tee -- to a point 3 or 4 inches beyond the wall. The drain, which is usually 2-inch plastic pipe, maintains a minimum slope of 1/4 inch per foot from the stub-out to the point where it ties into a main waste pipe.
Hereof, what is an electrical stub out?
By Cassandra Tribe. Pipe stub outs are the sections of pipe that feed from the lines run underneath a slab or building, through the slab, then connect to appliances, or eventually continue on to the upper levels of your building.
What is a pipe stub?
Pipe Stub Out Pipe stub outs are pipes that stick out from a wall or pipe tee. Stub outs are also called stub-ups. They are capped until a branch pipe is attached. The branch pipe can be inserted after the pipe cap is removed.
24 Related Question Answers Found
What is a water stub?
Stub Out. The pipes that go to the toilets, sinks, showers and drains--as well as any pipes that vent to the roof--must be in place and tested before the walls are added. The process of laying these pipes, and putting protective plugs or caps to keep building debris out, is called a plumbing stub out.
What is a PEX stub out used for?
Stub out elbows primarily used when installing PEX pipe for plumbing applications and are used to stub out of the wall and allow for further connection of outlet stop valves and plumbing fixtures. PEX stub out elbows with ears can be nailed to a wooden surface, such as a stud.
What are stubbed utilities?
STUBBED-IN UTILITIES means-- usually-- plumbing i.e. gas, drain, waste and vent (DWV) and water supply, brought to the point of a rough inspection whereby walls can be closed up and the owner, tenant or buyer need only connect appliances and fixtures to make for a functional installation, at which point a final
How do you run PEX through existing walls?
A lesson on your home plumbing system - how it is set up and how it works. drill through sud and sill plate. Drill Through the Stud and Sill Plate. use nail plate as added precaution. Run the Water Lines. crimps are most crucial part of project. position fittings and solder in place. connect water lines to manifold.
How do you rough in plumbing?
Steps for Roughing in your Plumbing: Step 1)Mark Key Locations. Determine where all the toilets will be and mark its center on the wall and measure out 13 1/2 inches from that point. Step 2) Cut the Drain Hole. Step 3) Drain Pipe Installation. Step 4) Supply Line Installation.
How do you install PEX pipe in a bathroom sink?
It's pretty simple to use PEX. SharkBite recommends crimp rings be 1/8" to 1/4" from the end of the PEX. Slide your crimp ring over the PEX then the fitting into the pipe. Use your crimper at a 90 degree angle to the PEX and compress the crimp ring.
What is a stub up?
The 'Stub-up', or 90º bend is usually the first bend that an electrician learns. A 90º bend simply consists of one 90º bend at a desired distance from one end of a length of conduit.
Can a toilet and shower share the same drain?
Your shower drain can connect to the toilet drain, but it cannot connect to the toilet trap arm. So if your "main drain connection" is also the vent for the toilet, the line from the closet flange to the main drain connection is trap arm and the answer is no, the shower cannot tie in here.
Can two toilets share the same drain?
Most houses have more than one toilet, and if they are on the same side of the house, their waste lines can usually tie into the same stack. If they are on opposite sides, however, each may need its own stack. Since the stacks must be vented, this would mean two vent openings on the roof.
How far should a toilet be from a wall?
Standard drywall is 1/2 inch thick, so the plumber should set the toilet flange at least 15-1/2 inches from the center of the flange to the wall framing. The standard distance from the back wall is 12 inches, or 12-1/2 inches from the center of the flange to the wall framing.
What is the difference between a 10 and 12 rough in toilet?
Those numbers are a measure of the distance between the wall and the center of the closet flange (aka, where the johnny bolts that secure the toilet bowl go). Most toilet bowls will work with either a 10″ or a 12″ distance, but a 10″ rough tank is slimmer to allow for the decreased distance.
Source: https://askinglot.com/what-does-stub-out-mean-in-plumbing
Tidak ada komentar:
Posting Komentar